• Advantages of Flexographic Printing 21-04-09

    Flexography remains the most commonly used print process in the label industry. There can be no flexo label without the proper plate and therefore the proper plate making equipment. Industry leaders have stayed on top of the trends, ensuring that labels are printed in the quickest timeframe and with the highest quality. Printing is done using flexible sheets, which were initially made from natural rubber, then synthetic rubber and now mainly from photosensitive polymers. Flexographic printing is done on paper, cardboard or plastic film. Liquid inks with low viscosity are used for printing. These include water-based inks, solvents and ultraviolet (UV) curing inks. Non-absorbent substrates (films) are mainly printed using UV and solvent-based inks, but water-based inks are increasingly used due to their ecological aspects and increasing adaptability. Flexographic Printing Flexographic printing, or Flexo, is a technique for bulk printing using flexible relief plates. The manufacturer applies the ink first on the plate and then on the surface. This is a low-cost printing method, and it has progressed much since 1970 after direct laser engraving was introduced. Lithographic printing or Litho is a method of printing, initially based on the unmixable materials of oil and water. Lithography is used for anything that needs vibrant colours and is printed in large quantities. However, the printing method you’re employing needs to be useful as well as cost-effective. For custom printing, flexographic vs lithographic is an age-old debate, as these two are conventional methods in the printing and packaging industry. Nonetheless, when we speak of corrugated boxes, we need then in bulk. Bulk printing is a tedious task and does require some level of optimization. Factors like budget at hand, time constraints, quality of the print, and how boxes are going to be used - shipping or retail come into play. Printing Process Flexographic printing requires an initial setup cost. Flexo uses flexible plates mounted on a cylinder. The manufacturer uses a partially immersed ink roller to apply ink on an anilox roll. The anilox roll is a hard cylinder, usually made from steel or aluminium with a ceramic outer layer that comes with many dimples. The manufacturer uses the anilox to distribute the ink on the flexo printing plate uniformly. In the flexographic printing process, the ink is metered onto the surface of the plate by an engraved/etched roller of chrome or ceramic similar to a gravure cylinder but with a uniform distribution of cells (size, shape and depth). This roller is called an ‘anilox’. The corrugated boards run directly between the impression cylinder and the paint roller. Finally, the manufacturer runs the substrate through a dryer to prevent smudging. Flexographic printing is used on everything from food wrappers to secondary containers, such as cereal boxes to shipping cartons. The photopolymerizable material on a flexographic printing plate cross-links when ...

    Read More
  • Flexographic Product Packaging Design 21-03-23

    Digital flexographic printing is a plate making technology that uses a laser to directly expose the flexographic photosensitive polymer plates. It has the following advantages. Advantages of digital flexographic printing  ①The process is simple and the preparation time is greatly reduced. ②Exposure time is independent of pattern type and dot density. ③Replacing the separation sheet with shaded metameric material eliminates the dot distortion caused by the separation sheet processing. ④The main exposure, there is no diffuse reflection of light caused by the phenomenon of dot gain, you can get a clear dot. ⑤ Realization of direct plate making without soft film, the layout will not be flooded with dirty spots and defective. From the characteristics of the digital flexographic printing plate , digital flexographic printing plate can obtain fine, clear and high quality flexo plates. Therefore, in order to improve the quality of flexo printing, the use of digital flexographic printing plate is imperative. In order to make the designed products meet the printing requirements, flexographic product packaging design staff should pay attention to the following points when designing. 1. In the use of color, should be as simple, bright, bright colors If the design of the product overprinting too many colors, will cause the color dim. Due to the larger amount of flexo printing dot expansion, small dot loss is more serious, the pattern in a certain area overprinted color version too much, each color version of the problem of dot expansion or loss, dot expansion or extinction network phenomenon will be repeatedly flooded, making the picture dim, the lack of highlights and the middle tone sector, dot transition uneven, very disgraceful. Therefore, in the same full expression of the design of the draft conditions, should be as far as possible to reduce the number of printed colors to a minimum, which is very beneficial for the bulk production of printing manipulation, quality control and cost control. 2. Try to use spot colors to make up for the lack of four-color printing Many customers of packaging products always ask the design staff in the design of their products made of yellow, magenta, cyan, black four colors overprinted more than ten colors of the manuscript, but sometimes not only through the three primary colors or conventional four colors can simply show the entire color world, additional ports with a spot color long and short necessary, but also long and short an effective method. One-sided exaggerated overprinting overlay color is not desirable. Flexographic printing machine is ideal for printing large areas of the field and spot colors, flexographic printing machine mostly six or eight colors, only four colors will cause the unit idle, and four-color printing effect than offset or gravure, affecting the quality of flexographic products. 3. Should not use too fine lines and too smal...

    Read More
  • What Are Flexographic Printing Plates? 21-03-11

    Flexographic printing plates are flexible photopolymer plates used in flexographic printing to transfer ink and images onto a flexible substrate, such as paper or film. The printing plate is the key element of the flexographic printing process and the quality of the printed image depends to a large extent on the quality of the flexographic plate used. The flexographic process itself is renowned for its adaptability to printing on all types of flexible substrates, and the plate can be used and reused in millions of impressions. Here you will learn how the plates are made and how they function. The plates are carefully designed, which means that the printing surface is raised where the image is exposed. After the ink has been applied to the plate, the plate surface is the only area that comes into contact with the substrate. The area that is etched or embossed does not come into contact with the ink. Flexographic printing was originally made from rubber, but today it is made in sheet form from a photosensitive polymeric material, which distinguishes it from the fixed metal printing plates of offset printing. The plates are flexible enough to be wrapped around a cylindrical printing/plate roller. Plate processing 1) Traditional method The desired image is first exposed to the negative film using a laser phototypesetter. It is then placed directly on the surface material of the unexposed plate and held in place by a vacuum cover. The plate and film are then exposed to UV light to fix the image into the polymer material. Only the transparent areas of the negative will allow UV light to pass through, thus allowing the UV light to alter the molecular bonds in the photosensitive polymer material.  After sufficient exposure time, the plate is fixed to an oscillating platform and then immersed in a rinse tank. The rinsing solution can be water or solvent, depending on the type of plate. The unexposed areas of the polymer are then rinsed off the plate base by means of a rinsing brush. The waste polymer is dissolved into the rinse solution and then disposed of for recycling/solvent recovery. After the rinsing process, the plate is placed in a hot air dryer where the excess water/solvent is evaporated, leaving a dry plate. Post-curing with both UVA and UVC lamps is then required, after which the finished plate is ready for use. 2) Digital printing plates Today, most flexographic plates are exposed using direct "computer-to-plate" technology (CTP). In this case, the unexposed negative film is pre-laminated to a photosensitive polymer sheet so that both layers can be exposed in the same device. A computer-guided laser first exposes the negative layer and then exposes the photosensitive polymer to a UVA light source. This exposure technique produces a higher quality plate than conventional methods. The exposed plate is then processed using the processing method described above. 3)Thermal processing of flexographic plates As mentioned above, although exposur...

    Read More
Middle Size Flexographic Photopolymer Plate Washing Machine
  • Item NO.:

  • Payment:

    30% T/T deposit, 70% T/T before shipping
  • Market Price:

  • Product Origin:

  • Color:

    Silver grey
  • Shipping Port:

  • Lead Time: 

    30 workdays
contact now
Product Description


Middle Size Flexographic Photopolymer Plate Washing Machine



2.Specifications & Parameters

Model:ALD06-5280                                                                        Plate washing size(mm):2030x1320           

Washing Machine size(mm):4030*2000*1200                            Voltage (V):380V




The series equipment including KMF-LE Lifting type exposure machine,KMF-LD de-tacker/drying combination machine and KMF-AW automatic connection type of washing machine .


1.)KMF-LE Lifting type exposure machine


Exposure unit for lifting type, using imported UVA lamp.This unit configure thermostatic radiator ,to avoid high temperature heating cause unstable vacuuming during high network plate making process.


2.)KMF-LD de-tacker/drying combination machine



De-tacker unit is drawer, using imported UVC lamp and sino-foreign joint venture production of philips ballast.the baseboard of light treatment drawer is made up of corrosion resistant epoxy board, slide way is made of stainless steel, prevent ozone then can not corroding metal and soil plate. This unit configure strong powerful exhaust device, for exhaust ozone airflow.

Drying unit is drawer, set 2 drawer drying, there are three side can blow hot air and circulation structure, can guarantee that all around the evenness of temperature, range of temperature between ± 5 ℃ difference within. Automatic timing, automatic constant temperature, and alarm, configure automatic constant temperature exhaust function, and can effectively guarantee and the drying temperature conditions, automatic emissions caused by dry timely and penetration in the flexible plate of ozone in chemical solvents, the drying speed, the energy conservation.


3.)KM-AW Automatic connection type Flexible plate washing machine


This machine adopts touch screen control system,it can be automatic pressure positioning,automatic constant solvent temperature, automatic pump in and discharge solvent,high pressure blow.Wash unit is made of 304 # stainless steel .it use PLC to adjust wash pressure,stores up different thickness version material,the thickness is 0.01-7.00mm that choose by PLC controler .Brush is made of best nylon bristle, the way of wash is flat brush + round rolling brush mixed crisscross move ,suitable for requirement of high precision.Wash version can be infinitely long, uninterrupted large production of flexo produce.

inquiry now
Related Products
  • Exposure machine Flexographic Photopolymer Plate Exposure Machine

    Condition: New Application: Making Flexo Plate Packaging Type: Crate Packaging Material: Wood Automatic Grade: Semi-Automatic Driven Type: Electric Voltage: 380V Power: 7 KW Place of Origin: Jiangsu, China (Mainland) Brand Name: AOLIDE Weight: 900kg Certification: CE Certificate After-sales Service Provided: Overseas third-party support available Plate-Making Size: 2030x1320 Light Source: UV Light Printing Style: Flexo Printing UVA Lamp: 80W UVC Lamp: 36W Exposure Machine size: 3000*1750*2100mm

  • Exposure machine Flexographic Photopolymer Plate Exposure Machine

    Condition: New Application: Making Flexo Plate Packaging Type: Crate Packaging Material: Wood Automatic Grade: Semi-Automatic Driven Type: Electric Voltage: 380V Power: 7 KW Place of Origin: Jiangsu, China (Mainland) Brand Name: AOLIDE Weight: 900kg Certification: CE Certificate After-sales Service Provided: Overseas third-party support available Plate-Making Size: 2030x1320 Light Source: UV Light Printing Style: Flexo Printing UVA Lamp: 80W UVC Lamp: 36W Exposure Machine size: 3000*1750*2100mm

  • Water Flexo Plate Making Machine Flexo Plate Making Machine with a Circulation Water Tank

    1.Name: Flexo Plate Making Machine with a Circulation Water Tank   2.Specifications & Parameters Model Plate-Making Size Dimension Power Power Net Weight JS550 550 X 350 800 X 750 X 1000 220V 50HZ 2.2KW 250KG JS400 420 X 300 650 X 600 X 1000 220V 50HZ 1.8KW 200KG JS750 750 X 500 1100 X 1000 X 1050 220V 50HZ 1.5KW 200KG JS900 900 X 600 1250 X 1100 X 1050 220V 50HZ 2.0KW 310KG JS1200 1200 X 800 1450 X 1200 X 1050 220V 50HZ 2.2KW 380KG 3.Description 1. It is made of stainless steel shell, featuring in durability and won’t get rusty. 2. Adopt imported PHILIPS specification printer lamp, rectifier. 3. Imported slow reflective violet suction membrane. 4. Computer controller enables it to be easily operated. 5. Adopt American digital integrated them to sensor. 6. Fully automatic printing plate washer assembled with imported green sheet-sicking device. 7. Japanese Panasonic or oriental printing plate washer, Japanese ORIX constant dry oven featuring in strong wind. 8. Computer micro-controller program control, full electronic digital display. 9. It is a good equipment, which integrated exposure, printing plate washer    and drier. 4.Pictures If any request please contact me directly     Skype:szaolide002       Whatsapp:008618051104201 

  • Photopolymer printing machine Flexo Printing Plate Making Machine

    Packaging & Delivery Packaging Details: Standard export packaging. Delivery Detail: 15-20 workdays This model combined machine with expoeure,washout.drying and glur-clean-clan process.Main units are imported. The surface is made of stainless stell. Copy:Directly copy from film. Exposure:Short time exposure as imported lamp. Dry:IR dry,temperature is made of stainless steel. Clean:Import clean system,short time for cleaning. Available making plate area size:450x750mm,420x300mm,900x600mm,1200x800mm,400x600mm. If any request please contact me directly     Skype:szaolide002       Whatsapp:008618051104201